Installed on Initial ModelGSX1300R HAYABUSA
I've seen this product a lot, so I was curious to see how effective it was.
I hadn't been able to get my hands on it because I thought it was too expensive, but I took the plunge and decided to buy it and it was the right decision.
Knee grip requires very little effort, so touring fatigue is significantly reduced.
It prevents the seating position from shifting forward.
Stable when Hanging on
and it is also very good in terms of Riding Position.
ThornThorn is pretty intense, so it might hurt a little if you wear thin Pants.
(Denim would be Large sturdy)
Also, I'm a little worried about the Pants side if you wear leather pants.
It's not the easiest category to apply.
The adhesive strength of the bonding surface is considerable, so if you do not position it properly, you will be in tears.
Also, because of the mucus, it is difficult to apply while removing the air, so I recommend applying Black unless you have a lot of hail.
([Color] If you use Clear, you can see the air bite and the place where it was reapplied)
If you think of it as just a Rubber Seat, you can't deny that the price is rather high, but since it's not cut and molded, it's probably not a bad price for a motorcycle product that can't be produced in quantity.
Also, if you think about the effect of the installation, there is a benefit that can pay for this price, so I don't think you will regret buying it.
56.05 EUR (9,680 JPY)
Informations de livraison
-
Please select product form first.
Conforme
-
GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
02-15
Détail du produit
**Stomp Grip adhesive needs 24 hours to stabilize its adhesive strength.Full adhesion requires 72 hours.If you use the product before it is fully bonded, it may peel off or shift.
*Please pay special attention to the use of stomp grips that are attached to the frame surface.
*When driving a vehicle equipped with stomp grips, please wear clothing that does not allow your bare skin to come into direct contact with the stomp grips.If you drive with your bare skin in direct contact with the product, you may suffer from abrasions and other injuries.
The adhesive used in Stomp Grip is very strong.If you remove the stomp grips forcibly, the paint may come off with them.To remove the Stomp Grip, heat it up with a heat gun or the like to reduce its adhesive strength, and then remove it.
(It depends on the paint condition of the vehicle, but older vehicles need special attention)
*We do not accept returns or exchanges after the package has been opened.
*Because of the shared stock system with the store, there is the case that it is out of stock by the purchase timing regardless of the stock display.If the item is not in stock, we will order it for you.
*Please make sure to check the year of your vehicle before ordering..
While most of the products are just a sticker to prevent scratches on the body, the Stomp Grip is a riding support gear that has evolved into a functional part to reduce fatigue.
From the street to the circuit, it is highly supported in various situations.
Originally developed elastomer material, strong 3M adhesive is used for the adhesive.
The pad keeps its original gripping power without shifting even in hard riding scenes.
MADE IN THE USA!
Stomp Grip is used by top racers and stunt riders all over the world.
It is very popular in the circuit and the street in Japan.
Stomp Grip users are increasing all over the world.
[stomping on stomp grips]
1. Clean the surface to be applied.
(When using clear, please remove dirt and water stains with compound before starting work)
2. Degrease the surface to be applied.
3. Perform positioning.
4. Apply from the edge so that air does not enter.Peel off the backing paper while pasting.
(If you use a clear sheet, apply it slowly and carefully, taking your time from the edge.It is possible to stick it beautifully without air entering.)
The adhesive of Stomp Grip needs 24 hours to stabilize the adhesive strength.
Full adhesion requires 72 hours.
If you use the product before it is fully bonded, it may peel off or shift.
Prudence
* S'il y a un mode d'emploi inclus, il sera en japonais.
LIENS DES PAGES MODÈLES
NOUVEAUX ARRIVAGES DE PIÈCES D'OCCASION POUR
NOUVEAUX ARRIVAGES DE PIÈCES D'OCCASION POUR
NOUVEAUX ARRIVAGES DE PIÈCES D'OCCASION POUR
Nouveaux arrivages de produits d'occasion
Nouveaux arrivages de produits d'occasion
Produits prêts à être expédiés depuis le stock
Avis des clients
Reviews with image
![whole [Color] It's not Clear.](https://global-fs.webike-cdn.net/photo/impression/51/51e90f8b9d6816d93e66eb7393a297fbM.jpg)
Fits:SUZUKI GSX1300R Hayabusa 02-15
Dec 8, 2021
It's expensive, but you won't regret it.
Fits:SUZUKI GSX1300R Hayabusa 02-15
Dec 16, 2020
Racing suit's inner knee is shaved
I installed it in the Busa of the 2009 CanadaMODEL which I acquired from my brother. The inner knee part of the racing suit is shaved off.
The non-slip sheet fabric was better for holding me in place than this one.
However, it looks cool, so it's good!
Fits:SUZUKI GSX1300R Hayabusa 02-15
Feb 28, 2017
I thought that I do not have to slip when riding with jeans and I bought it.
Although it looks awful, I expect it for performance.
Since TankCarbon was installed, I installed it with some processing.
Because my friend helped me, I was able to install it unexpectedly easily.
But I think Hair Dryer is an essential item.
Fits:SUZUKI GSX1300R Hayabusa 02-15
Dec 7, 2016
【What made you decide the purchase?】 Since it will be diverted, this was only by comparison of Tank size
【How was it actually used?】 Since I am using it on another vehicle, the feeling of Grip is the best
【Was it difficult to install? (Hard parts case)】 Although it is Clear, you can stick it cleanly if you put it neatly
【Please tell me the point of installation and hang (in the case of Hard parts)】 Position firmly and blow water with firm misting and paste from the projected part, Air will not enter
【Have you compared items?】 For GSX 1300 R, only this is hit, ZZr 1100 or Lineup does not have it, shape it select this
[Others] When warming too much at the time of pasting it will stretch so it feels like warming with Hair dryer is just fine
Although it can not be said that wear and tear of Pants is not said, Riding becomes considerably easy and we can afford.
Although it is not a cheap one, I thought it was appropriate to consider fatigue.
Fits:SUZUKI GSX1300R Hayabusa 02-15
Dec 15, 2015
When used in conjunction with Carbon Tank Protector, Pad interferes, so I cut out like a photo.
Because it holds firmly at Breaking, thigh does not slip a lot.
It might be difficult to get on without using thick G pan (Lol)
After all Clear is hard to paste or air bubbles are conspicuous.
We recommend dare to dark blue car.
It might be hard to stand out because it is White.
New Custom Articles
