It broke at the time of putting in the round part of Lever's tip.
Parkari I do not slip at all even if I buy it.
Grip is Pro Grip of Large justice
Lever grip is ...
As a result it has been split without terminating it.
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
1 / 5
1 Les avis
rating breakdown
5 Stars | 0 | |
---|---|---|
4 Stars | 0 | |
3 Stars | 0 | |
2 Stars | 0 | |
1 Stars | 1 |
It broke at the time of putting in the round part of Lever's tip.
Parkari I do not slip at all even if I buy it.
Grip is Pro Grip of Large justice
Lever grip is ...
As a result it has been split without terminating it.
I used it for PCX.
Should I have a little more length?
There was little Size Exactly for Honda's Lever.
Yamaha's Scooter's Lever was Exactly.
While installing the detergent, I put it while sliding, but it broke a bit. I think that it is better than Sponge type's one.View Detail
It was attached to xr 250 before. First of all, Material : Rubber is good but Length is insufficient After 2 centimeters long it is good If it may be unavoidable on the material, but if you use it
Rubber twisted, so I used it a lot and lost it
Currently I use Silicon tube but this one is pretty good. I think that it is good as a product of this hand to those who are said to be not dedicated.View Detail
【What made you decide the purchase?】
In the midwinter the Left fingers were getting cold and in trouble.
【How was it actually used?】
The feeling of coolness from Lever decreases, and Touch does not feel uncomfortable.
【Was it difficult to install? (Hard parts case)】
I had a hard time installing it. I was prepared to look at other people's impressions beforehand.
【Please tell me the point of installation and hang (in the case of Hard parts)】
I also prepared a Compressor, but in the end I just used a neutral detergent and water in Spray. As you turn it up, you go in and get in. If somehow we could attach one, we could do surprisingly quickly the second time. Work on a cold day does not recommend because Rubber will cure.
[Is there anything I was disappointed about?]
There is nothing special now.. I would be happy if the durability is good.
【Hope for Manufacturer - Please let me know if you have any improvement points]
It will be in millimeters, but it may be a little longer.
【Have you compared items?】
I also have a Sponge type, but I chose this Rubber type considering Touch and durability.
[Others]
I bought Black because Lever was Black, but if you color it differently from Lever it will be Dress-up as well.View Detail
Lever is easy to grasp by installing it, and it will not slip again.
Because it has various colors, it can be used as an appearance Custom.
However, the installation is Large strange is Minus.
As a hang of installation, I first apply LETTER to LeverBody to make it slippery. Next, wind and grip Lever grip with Towel. Then you plug in Lever with your strength. I need familiarity and power, but I can not take it if I can attach it. Although it may slide with detergent at the beginning, please try as it will not slip if it dries.View Detail
I've been using a red sponge type one, but I felt like unifying the color to black and green, and so I bought this part.
I can't compare it to my former one because the material is completely different.
But it doesn't slip and you won't get tired.
Your fingers will not slip even if you lightly apply the brake using the tip of your finger.
It will be a small decoration too.
It depends on your taste, but its performance level is what I really dreamed of.
The installation was quite hard, though.
Here's some advice.
First, you will find it difficult to pierce the tip.
You need to open it and press it in with both hands.
If you succeed that part, then you need to press in the remaining half, and then push up the upper half again.
That's how it goes. If you repeat this process it will fit in smoothly, I guess.
It won't move a bit if you try to press the upper part and the lower part simultaneously.
It says to refrain from using any solvents, but I applied some parts cleaner, because it didn't move.
There's no problem up till now.
Just apply a little and push the upper half, and then the lower half.
Finally adjust it to the place where your finger touches when actually applying the brake.
Though it was hard to install, I am satisfied with its performance for now I can grip the brake without slipping.
I also like it because the color has been unified to black and green.View Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Service Clients
INFORMATION
A PROPOS DE NOUS
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING