Avec l'unité Lumière
[Taille]
Largeur : environ 760 mm
Longueur approximative : environ 500 mm
Diamètre extérieur : environ. 520mm
[Matériel]
FRP
Capacité
CowlBody, Jeu de supports, Écran, Jeu de vis de l'écran
*Veillez à vérifier les précautions avant d'acheter.
*La lumière utilise un "projecteur à LED de 7 pouces" et le même type d'unité lumineuse.
*Ce capuchon est un produit universel fabriqué à l'étranger. Veuillez vous assurer de lire et de comprendre les points suivants avant d'acheter.
*Il y a un cas où l'unité d'éclairage et le capot entrent en contact l'un avec l'autre, auquel cas vous devez supprimer le point d'interférence du capot.
*Le capot peut entrer en contact avec la fourchette.
*Les autres parties qui interfèrent doivent être coupées ou rognées.
*L'unité d'éclairage fermée doit être étendue à partir du harnais principal.
*En fonction de la position du capot, il est possible que le trou entre l'étai et le capot ne soit pas aligné. Dans ce cas, il faut élargir le trou du capot.
*Dans ce cas, vous devez fixer l'écran et le trou du capot avec l'écrou du puits et élargir la partie non adaptée par ponçage.
*Selon le lot, il y a des lots qui n'ont pas de trou du côté du capot pour l'écran. Dans ce cas, vous devez percer les trous afin d'adapter l'écran.
*Nous ne pouvons pas répondre à d'autres questions que celles énumérées ici.
*Nous n'acceptons aucun retour du produit s'il ne peut être installé parce qu'il s'agit d'un produit à traiter.
*Avant de peindre, veuillez traiter et installer le produit. Nous n'acceptons aucune réclamation après la peinture.
*Veuillez noter que les spécifications du produit peuvent changer pour des raisons liées au fabricant.
With light unit
[Size]
Width: Approx. 760mm
Front and rear length: Approx. 500mm
Height: Approx. 520mm
[Material]
FRP
[Components]
Cowl body, bracket set, windshield, windshield screw set
*Please make sure to read the notes before purchasing.
*7 inch projector LED headlight unit and the same type of light unit are used for the lights.
*Because this cowl is a universal product made non Japanese, it may have some scratches and scuffs, and the holes may not fit, so some modification is required for installation.Please make sure you understand the following information before purchasing.
*The light unit and cowl may interfere with each other, in which case it is necessary to shave the interfering part of the cowl.
*There is a case that the fork and the cowl interfere with each other, check the range of movement of both sides and if it interferes, it is necessary to shave the cowl.
*Other interfering parts need to be cut or shaved.
*The supplied light unit requires an extension harness to be fabricated from the main harness.
*Depending on the positioning of the cowl, the hole between the bracket and the cowl may be misaligned.To do this, you will need to widen the hole in the cowl.
*In some cases, the holes of the windshield and the cowl do not match, in that case, you need to fix the windshield with the well nut from the center hole of the cowl to the outside, and widen the holes with a file in order.
*Depending on the lot, some of them do not have the hole for the windshield on the cowl side.In this case, please drill the holes in order to match the windshield.
We will not provide information about processing methods other than those mentioned here, so please verify according to your actual bike.
*Any returns will not be accepted due to inability to install the product.
*Please be sure to process and install before painting.Any claims after painting are not accepted.
*There may be changes in product specifications due to the manufacturer's reasons.