- I owned an SR400 and the carb fit so tightly inside the frame so I cannot adjust the idle screw. Thankfully I've found this product for my carb and even my bike.Lire la suite
- fits:
- KAWASAKI Z1300/KZ1300
Another great product from Bito JB power. Best customer service in the industry. Quality was top of the line and they operate flawlessly. Deeply impressed. Lire la suite - fits:
- KAWASAKI Z1 (900SUPER4)
- KAWASAKI Z2 (750RS/Z750FOUR)
fast postage.great looking carbs.made the bike run great right out of the box.this is the way to go beats messing around with old carbsLire la suite - fits:
- SUZUKI BANDIT400
Loving these 33mm FCR carbs! Bike is a 1992 GSF 400 with .04 over Suzki pistons and gk73 GSXR 400 camshafts.
Tune: 125 Main Fuel Jet, 200 Main Air Jet, 42 Slow Jet, 2 1/2 turns out on fuel screw, 3/4...Lire la suite - fits:
- KAWASAKI Z1 (900SUPER4)
- KAWASAKI Z2 (750RS/Z750FOUR)
The engine starts better and the acceleration performance is stronger without the mid-rotation stutter at the beginning of running. However, the fuel is still too rich and there is a lot of black smok...Lire la suite - The length is that of the FCR Carburetor BodyOEM; note that there is a difference in this stop screw length between the Large Type carburetor and the Small Type carburetor.Simply fix the bracket to th...Lire la suite
- fits:
- KAWASAKI GPZ900R 84-03 (A1-A16)
OEMCVK #4Slide valve is worn out and sucks secondary air, so negative pressure is not stable. FCR was the only choice.Disassembled for inspection of each part and sprayed with Bell Hammer for bearing....Lire la suite - This Thruttle Stop screw is exactly the same length as the FCROEM. However, for installation in the Float chamber fixed Bolt section of #1Carburetor Bracket." is attached to the product. This Bracket ...Lire la suite
- fits:
- HONDA RVF400 (NC35)
- HONDA VFR400R (NC30)
The racing cabs are very easy to set up, and once you get the settings right, you will be amazed at the acceleration power you can get. However, setting is very difficult. It is very difficult to set ...Lire la suite - fits:
- YAMAHA XJR1200
- YAMAHA XJR1300
I can do the tuning myself if I try hard enough.It will take time and Jet supplies.I had it tuned by a PRO.Power is a lush.Lire la suite - fits:
- KAWASAKI ZRX1200R
I submitted a Setting in FunnelSpec.I had a one-off muffler in the car, so the basic setting did not match the fuel mixture.The fuel mixture was matched while changing the Jet.It is troublesome to rem...Lire la suite - fits:
- HONDA CBR250RR (MC22) 90-91
The one for MC22 was used on MC19.The OEM Throttle Wire was too long and did not fit, so I installed it without the return wire. (To be adjusted later by JB in the posterior Thailandco.)And the OEM wi...Lire la suite - I needed this adapter to attach the power filter to the FCR carburetor body and to prevent the carburetor body from leaking air. One of the adapters I had in storage was crushed into a flat piece, so ...Lire la suite
- fits:
- KAWASAKI ZXR750
안녕하세요
좋은제품 찾던중 위바이크를 알게돼서
레어한 카브레더를 발견해 구입까지 하게돼었습니다
진심 fcr카브레더는 최고중에 최고입니다
앞으로 위바이크에서 좋은가격에 좋은 제품 또다시 구입하지 싶습니다
항상 지금과 같은 위바이크 돼시고. 더욱 발전하는 위바이크가 돼길 바랍니다...Lire la suite - fits:
- HONDA CBX1000
The appearance is very good. They are factory cheched, unscratched and assembled straight and with an attention to details that shows a professional manner. The idle setting adjuster seen in Webike pi...Lire la suite - fits:
- KAWASAKI ZEPHYR750
I had a hard time with Setting. I heard that I could run the car on a pontoon, but the jetting was so thick that it didn't blow up at all, and it took me a while to get it running properly.I think it ...Lire la suite - Idling AdjusterIt's easy.Lire la suite
- fits:
- HONDA CB750F 79-84
- HONDA CB750 Four(CB750K) 79-80 (DOHC)
I went with CR because of the malfunctioning Normal cab.It was easy to replace and Idling normally in about Cell3 times.Afterwards, I only did Setting of the upper part, but it was a good feeling to t...Lire la suite - With this Parts, Remote is done by Left hand, but tightening and loosening may be lost by Left hand. It is not a problem if you get used to it. Also, it is thought that a few millimeters long Screw is...Lire la suite
- fits:
- SUZUKI BANDIT400
Great carbs for the Bandit 400! Please note; the OEM throttle assembly will not work and the OEM fuel valve will have difficulty delivering enough fuel. I suggest a qualified tuner set them up or ask ...Lire la suite
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING