- bought this OEM bolt when I needed to do work on my tdub engine.TDUB ,The flywheel is mounted onto the tapered end of the crankshaft. It is secured from rotating with a Woodruff key, and is tightened ...Lire la suite
- Great exactly what I need for fjr. It smells like an old item but its well oiled & kept. Parcel came in very well packed too though delivery took some time.Lire la suite
- I used to use wood screw for valve adjustment job in the past.This OEM tappet adjuster tool quality seems suitable for light work that it will see in a DIY .The square swivel does fit.I can use this ...Lire la suite
- Purchased to remove Locker Arm on xs250sp 4a8.I bought it without checking because it was mentioned in the tool section of the service manual and was also used in the photo of the procedure for removi...Lire la suite
- Since it is an OEM, I don't think this is the best way to go about it.I don't know until I need to be concerned about OEMs.Lire la suite
- Product well received, package was bubble wrapped delivery was fast. Highly recommended to buy. Tested Multimeter in good working order.Lire la suite
- Used for double-sided tape replacement of electrical components, etc.The adhesive strength is good and the quality is fine as it is made by 3M, which is a reliable company.Lire la suite
- The performance is very good and easy to use Tape.It is easy to use because it is not sticky even when used in areas that get hot from heat.The price is rather expensive, but it is definitely easier t...Lire la suite
- Uses 3M double-sided tape, which has an established reputation.In this temperature, it sticks strongly.Last week, I was using ButylTape.It didn't stick at all, so I tried again with 3M.I wasn't sure i...Lire la suite
- I bought it to watch PistonTop.It's great to be able to use it in the car as well as in the motorcycle.Plug holes are used to ensure stable gauge measurement.Lire la suite
- YamahaOEMDial gaugeSTANDThe Large variation is useful for viewing the upper dead center of the piston.Until now, I had to extend the Dial gauge and insert it into the Plug hole, but with this STAND, I...Lire la suite
- I bought this to remove the locker arm shaft from my SR400, but I didn't need to use the slide hammer. I didn't need to use the slide hammer. I just screwed it in and pulled lightly, and it came out e...Lire la suite
- I bought this to remove the locker arm shaft from my SR400, but I didn't need to use the slide hammer. I didn't need to use the slide hammer. I just screwed it in and pulled lightly, and it came out e...Lire la suite
- The adhesive strength seems to be strong. I put it on the place where there is a lot of vibration, but it doesn't seem to come off. It's been 2 weeks since I put it on and I've only driven 40km, so I'...Lire la suite
- [How is it used?TZr250R (3XV) I used it to remove the Flywheel from the generator inThere are cheaper MagnetPullers made in China, but I chose this product because it is an OEM Product, which is menti...Lire la suite
- Bonjour, je suis très satisfaite, du produit, envoi très rapide, très bonne communication, suivi de commande, je vous remercie pour cette prestation, cordialement Mme BROQUET
---------------------...Lire la suite - 1KT (TZr250) I used it in the I used the Universal Product one before, but it didn't come off well and the tool lost, so I bought the OEM Product. It was easy to use and came off easily with the OEM t...Lire la suite
- It's an OEM tool and I had no problems working with it.Lire la suite
- If you compare the price with cheap Vinyl Tape, it is more expensive, but the performance is very easy to use and maintenance is excellent. It is easy to use because it doesn't stick even if you use i...Lire la suite
- OEM tool with low price and reliable.There is a similar tool made in C country, but the price is not so different and the reliability is much different, so there is no Merit to challenge.I think it's ...Lire la suite
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING