- fits:
- HONDA
- HONDA
- HONDA
- HONDA
- HONDA
Filter is excellent quality. Have to cut and remove old paper filter. Foam filter is shipped dry so needs to be oiled. Do not remove all of the paper filter. Leave some paper to seal the new foam filt...Lire la suite - fits:
- HONDA
- HONDA
The front sprocket was changed from 14T to 15T keeping the rear sprocket the same. No modification needed at all. This is a slot-in replacement.
The sprocket makes the power delivery in 1st and 2nd l...Lire la suite - fits:
- HONDA CRF250L -20
- HONDA CRF250 RALLY -20
I learned about this Exhaust System on a blog during its development, and it was definitely the items I wanted if I was going to buy a CRF250Rally!However, I was initially going to buy ‘21model (This ...Lire la suite - fits:
- HONDA
I replaced it because I do a lot of off-road driving.The 13T Driven Sprocket makes touring a little more difficult, but I am satisfied with it for off-road use.Not recommended for On roadTouring Maine...Lire la suite - fits:
- YAMAHA SEROW250
It has much better legs and is helpful in times of need.It is a good point that the minimum ground clearance is not changed since it is not lowered by LINK.Touring about 100 km will not cause any pain...Lire la suite - fits:
- YAMAHA
There were no problems with the lower part of the Engine during touring on forest roads, as it provided sufficient protection from stepping stones and other obstacles.Thanks to the Flat shape, it was ...Lire la suite - fits:
- HONDA TLR200 MD09
- HONDA TL125(TLR125) JD06
If you install it bare, it will hit the bottom bolt protrusion of the Crankcase. This means that when you hit the GuardI'm about to split the Crankcase. I put a Spacer in the back Screw to float it.It...Lire la suite - fits:
- HONDA TLR200 MD09
- HONDA TL125(TLR125) JD06
If you put it on as it is, it will hit the protruding threaded part at the bottom of the engine. In street drivingIt is not inconvenient, but AttackTouring, the person who uses it like hitting the bot...Lire la suite - fits:
- YAMAHA
- YAMAHA
I bought this to convert the chain size of my SEROW250 from 428 to 520.I wanted the secondary reduction ratio to be as close to the OEM 3.2 as possible, but I decided to go with the 12, which is almos...Lire la suite - fits:
- HONDA
- HONDA
- HONDA
Anyway, it's a normal good product.If you have a Lever that doesn't have an adjustment mechanism, you can change it.Lire la suite - fits:
- YAMAHA
MySEROW225 which is used in the beast road Attack and Enduro main body has the Rear suspension from the time when I bought it as a used car.It had a hard spring in it, white spring so I guess it was m...Lire la suite - fits:
- YAMAHA SEROW250
154cm female rider.When I ride the SEROW 250, I always feel like I'm barely stopping on one foot, with both feet just barely touching the ground.With the Lowdown Seat installed, the seat is lowered by...Lire la suite - fits:
- KAWASAKI
Since the US only inported the Super Sherpa for a few years there are very few aftermarket parts available here. This is a super heavy duty plate that will protect. Only compaint to be honest is i wis...Lire la suite - fits:
- YAMAHA
I put it on to see what it was like.Less bouncing in the gullies.Because Spring itself became a little thick, it interferes with Air Cleaner BOX a little, but it is not enough to be concerned.Large Sa...Lire la suite - fits:
- HONDA TLR200 MD09
- HONDA TL125(TLR125) JD06
I installed it on my TL125.It arrived and I immediately removed the old Under Guard and installed it, but there was one problem.The bottom of the Crankcase hits the bulge of the Bolt. I tightened the ...Lire la suite - fits:
- HONDA CRF250L -20
- HONDA CRF250 RALLY -20
Cannot be attached to the current MD47.Interference with rear brake pedal areaO2 Sensor is too short to stayThe company is currently developing a new product.Lire la suite - fits:
- HONDA CRF250M MD38 only
- HONDA CRF250L MD38 only
Bought to replace existing stock 2013 CRF250L header that is rusting away. Perfect fit and beautiful look after running in and turns blue at the bend section. Seamless construction with minimum welds.Lire la suite - fits:
- YAMAHA XT250X 08-
Thank you very much for sending the product as soon as possible.It's a SEROW 250, but it's still Carburetor Vehicles, 16 years old.I had a hole in my Exhaust System and Silencer the other day and was ...Lire la suite - fits:
- YAMAHA SEROW250
- YAMAHA XG250 TRICKER XG250
I wanted to reduce the weight anyway, so I was looking for something lighter than OEM, and I found this Exhaust System.I think I increased the top speed of each GEAR by about 5-10km after replacing th...Lire la suite - fits:
- KAWASAKI KLX230SM
- KAWASAKI KLX230R S 23
- KAWASAKI KLX230
- KAWASAKI KLX230S 22 2BK-LX230A
I'm 178cm tall and my heels float in the Normal seat, but in this Seat I can put my heels on the ground.Since the vehicle is light, I don't mind the footing so much when driving on a relatively clean ...Lire la suite
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING